Ready-Mix Concrete

MATERIALS (Content of 1 m³ Product)

• Volume of cement and cement-like material: 13-15%
• Volume of Fine Aggregate: 30-35%
• Volume of Coarse Aggregate: 35-40%
• Volume of mixing water: 14-17%
• Volume of Chemical Additive: 0,3-0,6%

PREPARATION

This is a type of concrete produced under special control at fully automated plants by using selected and stockpiled raw materials. This type of concrete has controllable thermal development values, it can be produced as dmax 12 and 22 mm and it has a slump value of S3-S5 or SCC in terms of workability. These are special products which can be prepared in C 50/60 – C 100/115 strength classes and can be transferred along long distances on vertical and horizontal plane.

SETTING PERIOD

SKYBET® has a minimum consistency preservation period of 2 hours. Setting period can be adjusted optionally.

FEATURES

• High strength with low water / cement proportion,
• Low internal stress and minimum micro-crack formation thanks to controllable thermal development,
• Allows short stripping period, pumping to long distances and high floors, high durability.

AREAS OF USE

• Multi-floor office and residence structures,
• Structures which require casting on long distances on horizontal and vertical plane,
• Structures which require high strength and durability,
• Structures which require early strength and stripping period,
• Structures which require long-term resistance against environmental impacts.

CONSTRUCTION PROJECTS IN WHICH IT IS USED

• Spine Tower project - Maslak
• 42 Maslak project - Maslak
• CZK Farmers complex - Zincirlikuyu
• Tepe Prime - Ankara
• Bomonto Arista Business - Sisli
• Agaoglu 212 - Mahmutbey

MATERIALS (Content of 1 m³ Product)

• Volume of cement and cement-like material: 13-14%
• Volume of Fine Aggregate: 35-40%
• Volume of Coarse Aggregate: 30-35%
• Volume of mixing water: 14-17%
• Volume of Chemical Additive: 0,4-0,8%

PREPARATION

This is a type of concrete produced under special control at fully automated plants by using selected and stockpiled raw materials. It has a free flow value of 65-75 cm, a T50 period of 3,5 -5 sec., a minimum viscosity of 8 sec., and specs which can be raised equally on both directions by 7 m on the horizontal plane and flow without segregation by 10 m in horizontal concrete pouring. Concrete can be transferred to hard pouring conditions through specially designed fixed, city pumps and flexible pipes.

SETTING PERIOD

Elastic concrete can maintain its flow, viscosity, physical features and rheology for minimum 2 hours. Stripping period is 16 hours under usual weather conditions.

FEATURES

• In minimum strength class of C 35/45,
• Can be transferred to long distances on horizontal and vertical plane,
• Self compacting and settling on the densest elements without requirement for a vibrator,
• A special product offering a perfect surface quality with Dmax 12 mm aggregate.

AREAS OF USE

• Structures with dense reinforcement,
• Structures requiring smooth surfaces at superior quality,
• Reinforcement structures,
• Hard pouring conditions,
• Structures requiring impermeability and durability,
• Circumstances where vibration cannot be applied (underwater structures),
• Office, residence and art structures.

CONSTRUCTION PROJECTS IN WHICH IT IS USED

• Greater Istanbul Water Supply Second Stage Project,
• Bosphorus passage pipe-backfill concrete,
• MEB (Ministry of Education) school building reinforcement projects,
• Spine tower Maslak project,

MATERIALS (Content of 1 m³ Product)

• Volume of cement and cement-like material: 11-13%
• Volume of Fine Aggregate: 32-34%
• Volume of Coarse Aggregate: 37-39%
• Volume of mixing water: 11-12%
• Volume of Chemical Additive: 0,3-0,5%

PREPARATION

This is a type of concrete produced by a special system at fully automated plants by using selected and stockpiled raw materials qualifications of which are proven under local and international standards. Fresh concrete properties are maintained under control in frame of the quality plan of each trans-mixer at each blending during production and to the pump edge after production.

SETTING PERIOD

With specially selected Polymer additives used in its production, DURABET® maintains consistency for a minimum period of 2 hours.

FEATURES

• Produced in minimum strength class of C 40,
• Impermeability and minimum crack formation thanks to low water / cement proportion,
• Low thermal development thanks to specially designed cement,
• Durability with maximum performance against environmental impacts, no requirement for maintenance for 100 years.

AREAS OF USE

• Structures which require long-term resistance against severe environmental impacts,
• Underwater structures and structures in contact with underground water,
• Works of art such as viaducts, roads, tunnels, tube tunnels, bridges, etc.,
• Constructions of foundations and infrastructure,
• Structures exposed to impacts of sea water.

CONSTRUCTION PROJECTS IN WHICH IT IS USED

• Marmaray immersed tube tunnel, the project of the recent 100 years,
• Station and link structures,
• Mimar Sinan Mosque – West Atasehir.

MATERIALS (Content of 1 m³ Product)

• Volume of cement and cement-like material: 12-14%
• Volume of Fine Aggregate: 30-34%
• Volume of Coarse Aggregate: 37-40%
• Volume of mixing water: 12-13%
• Volume of Chemical Additive: 0.7-1,0%
• Micro-fiber

PREPARATION

This is a brand product produced under special control at fully automated plants by using specially developed chemical and mineral additives and selected and stockpiled raw materials.

SETTING PERIOD

REPABET® maintains initial consistency and has workability. Its setting period is adjustable. It has high early compressive and bending strength.

FEATURES

• Highly fluid,
• High resistance to abrasion,
• High early bending strength, controllable crack formation,
• Resistance to freezing- thawing impact and short period of time before service.

AREAS OF USE

• Repair of aprons and runways,
• Repair of concrete roads,
• Repair of industrial floors, and
• Repair of all floors which must be urgently opened to service.

MATERIALS (Content of 1 m³ Product)

• White Cement and White filler material 20 – 22%
• Volume of Fine Aggregate: 30-32%
• Volume of Coarse Aggregate: 30-32%
• Volume of mixing water: 16-18%
• Volume of Chemical Additive: 0,4-0,5%

PREPARATION

The basic feature of WHITEBET which differs this product from ordinary gray concrete is its natural white color. This whiteness of concrete is due to color and purity of raw materials. As the source, form, purity of raw materials to be used in concrete may cause huge differences in the appearance and color or concrete, it is highly important to supply and stockpile the materials in a controlled way. Moreover, cleaning of the equipment used in production, shipping and placement of concrete is of high significance. Produced in minimum consistency of S4 to obtain exposed concrete surfaces, concrete must be placed to exposed concrete forms prepared without being subject to segregation.

FEATURES

• WHITEBET in minimum strength class of C 30/37,
• Can be produced in a whiteness range of 72 – 78 % according to CIE color scale; a mix to be designed in conformity with the purpose of use can meet desired limit values in concrete durability tests.

AREAS OF USE

With its quality meeting art and architecture, engineering and technology, WHITEBET is used in many big projects on modern settlement areas.

CONSTRUCTION PROJECTS IN WHICH IT IS USED

• WHITEBET has been used in the new service building project for Municipality of Kahramanmaras
• On structural reinforced concrete elements and
• In a large number of decorative projects.

MATERIALS (Content of 1 m³ Product)

• Volume of cement and cement-like material: 10-16%
• Volume of Fine Aggregate: 35-40%
• Volume of Coarse Aggregate: 36-42%
• Volume of mixing water: 16-20%
• Volume of Chemical Additive: 0,3-0,6%
• Metallic or synthetic fiber

PREPARATION

These are special products produced at fully automated concrete plants by using specially designed formulations and specially selected raw materials, and adding synthetic and metallic fiber in pan mixer.

SETTING PERIOD

Setting period of FIBRABET® can be adjusted optionally although it behaves like standard concrete.

FEATURES

Synthetic fiber

• Contains polypropylene fiber.
• Can be used in all concrete classes Dmax 12mm-22mm.
• Type and rate of fiber is ascertained depending on application. As it is prepared in pan mixer, fiber is homogeneously distributed in concrete and creates a synthetic reinforcement.

Metallic fiber

• Contains steel fiber.
• Can be used in various consistency classes, aggregate grain diameters and concrete classes.
• The content of the formula is optimized according to steel fiber. Amount of steel fiber in metallic fiber concrete is ascertained depending on requirements of the area on which the concrete is used.
• Maximum aggregate size and thickness of the concrete to be poured are taken into consideration in selection of the size and type of steel fiber.
• Metallic fiber concrete has higher tensile and bending strength compared to standard concrete.